1.1 A burn must be treated by …
A covering the burnt area with butter - NSC Electrical Technology Digital - Question 1 - 2024 - Paper 1
Question 1
1.1 A burn must be treated by …
A covering the burnt area with butter.
B putting ice on the burn wound.
C puncturing the blisters.
D running cold water over the bur... show full transcript
Worked Solution & Example Answer:1.1 A burn must be treated by …
A covering the burnt area with butter - NSC Electrical Technology Digital - Question 1 - 2024 - Paper 1
Step 1
A burn must be treated by …
96%
114 rated
Only available for registered users.
Sign up now to view full answer, or log in if you already have an account!
Answer
The correct answer is C: puncturing the blisters. This method helps to alleviate pain and prevent infection.
Step 2
In an op-amp bistable multivibrator circuit the op amp operates as an/a …
99%
104 rated
Only available for registered users.
Sign up now to view full answer, or log in if you already have an account!
Answer
The correct answer is A: comparator. The op-amp functions to compare the input voltages and switches accordingly.
Step 3
A/an … changes its output state when a trigger pulse is received. It remains in that state for a time determined by the RC time constant. Thereafter it returns to its original state.
96%
101 rated
Only available for registered users.
Sign up now to view full answer, or log in if you already have an account!
Answer
The correct answer is C: monostable multivibrator. This circuit produces a single output pulse when triggered.
Step 4
A circuit used to change a sine wave into a square wave with the same frequency is a …
98%
120 rated
Only available for registered users.
Sign up now to view full answer, or log in if you already have an account!
Answer
The correct answer is B: Schmitt trigger. It effectively converts the analog input into a digital output.
Step 5
When a positive square wave is applied to the inverting input of an op-amp integrator and the non-inverting input is connected to ground, the capacitor will …
97%
117 rated
Only available for registered users.
Sign up now to view full answer, or log in if you already have an account!
Answer
The correct answer is A: charge exponentially to the supply voltage. The behavior of the integration circuit responds to the changes in input waveform.
Step 6
The 555 IC functions as a … in an astable mode operation.
97%
121 rated
Only available for registered users.
Sign up now to view full answer, or log in if you already have an account!
Answer
The correct answer is B: frequency divider. In astable mode, it continuously oscillates between two states.
Step 7
The main characteristics of operational amplifiers are …
96%
114 rated
Only available for registered users.
Sign up now to view full answer, or log in if you already have an account!
Answer
The correct answer is A: very high output impedance, low input impedance, high voltage gain and wide bandwidth. These characteristics define the performance of op-amps in various applications.
Step 8
A … output connects the transistor collector to the LED cathode.
99%
104 rated
Only available for registered users.
Sign up now to view full answer, or log in if you already have an account!
Answer
The correct answer is D: sinking. This configuration allows the current to flow through the LED.
Step 9
ONE method of displaying information in digital systems is through the use of a …
96%
101 rated
Only available for registered users.
Sign up now to view full answer, or log in if you already have an account!
Answer
The correct answer is B: light-emitting diode. LEDs are commonly used to indicate on/off states.
Step 10
An up/down counter is used as an application in …
98%
120 rated
Only available for registered users.
Sign up now to view full answer, or log in if you already have an account!
Answer
The correct answer is D: lifts. Up/down counters are crucial in controlling elevator systems.
Step 11
Choose the correct JK input combinations that will produce a '1' (high) on the output of the JK flip-flop:
97%
117 rated
Only available for registered users.
Sign up now to view full answer, or log in if you already have an account!
Answer
The correct answer is B: J = 1 and K = 0. This condition sets the output to high.
Step 12
Microcontrollers can be programmed in various ways. One of the methods to program a microcontroller is to use a flow chart. A flowchart is defined as ...
97%
121 rated
Only available for registered users.
Sign up now to view full answer, or log in if you already have an account!
Answer
The correct answer is A: block diagram with instructions in the order of execution. It visually represents the steps to be executed.
